- Home
- About us
- Blog
- Shop
-
- Brands
- ALL Brands List
- Acoustical Systems
- Analog Relax
- Antipodes Audio
- Astell & Kern
- Audio Hungary
- Audio Solutions
- AudioByte
- AudioCircle
- Audiomica Laboratory
- Canary Audio
- Canor Audio
- Chameleon Audio
- Clarisys Audio
- Farad Power Supplies
- Ferrum Audio
- Fezz Audio
- Fonolab
- Glanz
- HiFiMAN
- HoloAudio
- Icon Audio
- LAB 12
- LAIV
- LampizatOr
- Mega Acoustic
- Monrio Audio
- OLIO SPEC
- Origin Live
- Pachancko Labs
- Phasemation
- PLiXIR
- Questyle
- Reed
- Remton
- Revival Audio
- Riviera Audio
- Rockna Audio
- Sbooster
- Shelter
- Sigma Acoustics
- Signal Projects
- Sonnet Digital Audio
- SOtM Audio
- Soulsonic Speakers
- Soundtastic (Struss Audio)
- SPEC
- Synthesis
- Tedeska
- Tellurium Q
- Trafomatic Audio
- Tsakiridis Devices
- Vitus Audio
- Volumio
- Second Hand Deals
- Account
Description
Armboards & Mounting Position
It is certainly possible to fit the Origin Live and Rega tone arm to any deck, but sometimes you may either have to modify your existing armboard or acquire a new one. The tone arms require a single hole in the armboard or plinth – 24mm or 25mm in diameter to fit into. Once the arm is inserted through this hole, it is then secured by a large nut which clamps it onto the underside of the board.
The distance from the center of the arm hole to the center of the platter spindle needs to be 223mm plus or minus 3mm. The arms can rotate to be fixed at any angle. The length of the arm from its mounting hole center to the cartridge end of the arm is 240mm. The arm overhang from the pivot point to the rear is 50mm to the end of the counterweight stub.
For 12 Inch Arms Only The center of the 24mm diameter hole for the arm mount to the center of the platter spindle is 295.6mm plus or minus 1mm. The length of the arm from its mounting hole center to the cartridge end of the arm is 309mm. The overhang from the pivot point at the rear end is 50mm to the end of the counterweight stub.
3 Point Fixing of Newer Rega and OL Arms Below Encounter Level – In addition to the 24mm hole, the 3 point mounted arms need 3 small holes for M3 bolts to fasten the arm to the board. These holes are also pre-drilled – if they are not needed, then for cosmetic purposes, you can fit a black button head bolt in them.
Fitting to the Linn LP12
If you have a Linn LP12 turntable with a Linn arm, the arm hole on your current armboard will be in the wrong position (Linn arms mount at a distance of 211mm from the platter spindle). We can supply you with a pre-drilled armboard for the Origin Live and Rega arms at €45 – this board is identical to the Linn armboard but is missing the Linn Logo. Alternatively, you can get a blank arm-board from Linn and get it drilled. This is simple to fit and instructions are provided.
After fitting a new arm, you can find printable instructions for setting up your Linn at Linn Sondek LP12 turntable instructions.
Modifying Your Current Arm Board
If you modify your current armboard, you will need to cut out the board to locate the arm at the dimensions given above. This will leave you with a hole to the side of the arm. However, this can be hidden if you make up a large circular plate washer of black card, aluminum, or other material and glue this to the armboard – the spacing washers we supply with a new arm have an outside diameter of 48mm and will normally fulfill this function for most situations (the thickness of the washer is 1.5mm). The advantage of gluing the washer to the armboard is that it also locates the arm in the correct position.
Reviews
There are no reviews yet.